Looking for some 308 recipes

General reloading

Moderator: Grantness

Post Reply
User avatar
MrSlippyFist
Global Moderator
Posts: 7018
Joined: 27 Aug 2008, 12:44
custom title: Sweeper
Location: Spokane, WA
Contact:

Looking for some 308 recipes

Post by MrSlippyFist » 15 Nov 2008, 12:39

Finally got all my LC 308 brass prepped. I've got 168 gr FMJ, CCI BR2 primers and will be shooting thru my M1A. I'm going to use Varget. All my searching has yielded around 37 grains for a start point and 41 (roughly) for a max. Anyone got experience with this conglomeration?
Image
Embrace the Suck

Wollychop
Senior Member
Posts: 5447
Joined: 20 Aug 2008, 09:09
Location: MN

Re: Looking for some 308 recipes

Post by Wollychop » 15 Nov 2008, 13:09

You going to crimp?

:ponder: Hodgdon's data says 46 grains for the max

168 GR Hodgdon Varget .308" 2.800" (COAL) 42.0gr (START) 2520 (VEL) 41,200 CUP 46.0gr (MAX) 2731 (VEL) 50,600 CUP

I tend to modify the OAL to tailor to the rifle (depending on where you want the bullet to sit in relation to the rifling)

These plinkin' rounds your cookin up or are you looking for tac driving?

Keeping in mind you'll never be as good as m1ashot.
Last edited by Wollychop on 15 Nov 2008, 13:17, edited 1 time in total.

User avatar
f3rr37
Site Admin
Posts: 14666
Joined: 19 Aug 2008, 12:09

Re: Looking for some 308 recipes

Post by f3rr37 » 15 Nov 2008, 13:10

Wollychop wrote: Keeping in mind you'll never be as good as m1ashot.
Isn't that the truth :lmao:

User avatar
MrSlippyFist
Global Moderator
Posts: 7018
Joined: 27 Aug 2008, 12:44
custom title: Sweeper
Location: Spokane, WA
Contact:

Re: Looking for some 308 recipes

Post by MrSlippyFist » 15 Nov 2008, 14:08

Yeah I was going to crimp, and this will be military brass so I know the loads need to be lighter. Do I need to have someone shove my head in a urinal so I can get that competitive edge?
Image
Embrace the Suck

User avatar
Rapier1772
Global Moderator
Posts: 12162
Joined: 20 Aug 2008, 09:00
Location: American Falls, ID

Re: Looking for some 308 recipes

Post by Rapier1772 » 22 Jun 2013, 22:51

So it seems that my PTR is liking the hotter loads for accuracy. I am using IMR 4895 and Lyman's says the max is 45gr (150gr bullet) but the barrel on mine is longer than usual; I want to see if going higher would be of any use. Is there a rule of thumb for going over manual maximums?
Obviously for the FsN, increase at .1gr increments & watch for signs of overpressure.
But what about .308? Watch for signs of course but how much of an increment is reasonable? On one hand I don't want a KB but on the other, I don't want to waste my time/powder with loads that won't change much.

I won't be crimping - don't have a crimp die yet :?:

Any advice?
Contrary to popular belief, you CAN fix stupid - it's just illegal.
Tactical Search Instructions & tips: http://www.fivesevenforum.com/viewtopic.php?f=3&t=12045

User avatar
flyingirish04
Gold Member
Posts: 4783
Joined: 25 Aug 2008, 21:42
custom title: Mtn Man in Flatland
Location: Great Plains, USA

Re: Looking for some 308 recipes

Post by flyingirish04 » 22 Jun 2013, 23:09

40.5 gr Varget and 175 SMK was a load I used very accurately in past. But I have sold all my 308s years ago so there may be better options for powder and bullets now.

With rifles, I would increase by .2 to be absolutely safe. I admit to going up .5 at a time before, but got a pretty good gas blast once and stopped doing that.

And I don't see need to crimp at all. Should feed in M1A just fine.
Killed Two Stones with One Bird.

User avatar
Rapier1772
Global Moderator
Posts: 12162
Joined: 20 Aug 2008, 09:00
Location: American Falls, ID

Re: Looking for some 308 recipes

Post by Rapier1772 » 23 Jun 2013, 14:11

Done, thanks.

I went up a total of 2 grains over max so far, 4 rounds each. I'll pull down the ones not used if any.

EMS on standby :laugh:
Contrary to popular belief, you CAN fix stupid - it's just illegal.
Tactical Search Instructions & tips: http://www.fivesevenforum.com/viewtopic.php?f=3&t=12045

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests