Reloading equipment for 5.7x28mm
Moderator: Grantness
Re: Reloading equipment for 5.7x28mm
Should there be a small gap between barrel and receiver. Took them out and put new fac round in
When I closed the two components togeather. I could see a very small gap (brass)
Thank you ,Larry Baumann. PS90
When I closed the two components togeather. I could see a very small gap (brass)
Thank you ,Larry Baumann. PS90
-
- Junior Member
- Posts: 8
- Joined: 10 Sep 2014, 13:21
Re: Reloading equipment for 5.7x28mm
I have been loading 5.7 for about 4 years now and produce a variety of nastiness for both the gun range and any varmint that steps in front of my new addition to my PS90 (EOTech laser holographic weapons sight)
These are addictive once you start using one. Back to the reload info: Favorite powders are AA#7 for 50 grain & up bullets and vihtavuori N340 for up to 45 grain. Use a rock chucker single stage and refuse to change to anything different. The shell holder comes from ***********Elite Ammunition******** money well spent. The case trimmer -- RCBS but if you are going to load several invest in a Tungsten Carbide trim head as I load about 300 - 600 at a time. Note: trim length has been verified to work well at !.35 .
These are addictive once you start using one. Back to the reload info: Favorite powders are AA#7 for 50 grain & up bullets and vihtavuori N340 for up to 45 grain. Use a rock chucker single stage and refuse to change to anything different. The shell holder comes from ***********Elite Ammunition******** money well spent. The case trimmer -- RCBS but if you are going to load several invest in a Tungsten Carbide trim head as I load about 300 - 600 at a time. Note: trim length has been verified to work well at !.35 .
-
- Junior Member
- Posts: 8
- Joined: 10 Sep 2014, 13:21
Re: Reloading equipment for 5.7x28mm
I also have the 5.7 FN . It keeps my PS90 company when out in the wild
-
- Junior Member
- Posts: 8
- Joined: 10 Sep 2014, 13:21
Re: Reloading equipment for 5.7x28mm
Definition of A Buzzard: Anything undesirable that deserves to be shot!!!!!!!!shootinbuzzards wrote:I also have the 5.7 FN . It keeps my PS90 company when out in the wild
Re: Reloading equipment for 5.7x28mm
I've been reloading old brass for a while and have run into a few problems I felt worth noting.
The RCBS shell holder destroys the rim because it has a lip on it that becomes imprinted in the brass. the Brass is also loose and wobbly in it leading to laquer scraping off one side and bullets seating cocked. In my opinion it makes it fairly unusable.
I have a Redding shell holder thats on the way, should work as it doesnt have the step. Any others experiencing this? Why has no one made a proper shell holder for single stage presses?
The RCBS shell holder destroys the rim because it has a lip on it that becomes imprinted in the brass. the Brass is also loose and wobbly in it leading to laquer scraping off one side and bullets seating cocked. In my opinion it makes it fairly unusable.
I have a Redding shell holder thats on the way, should work as it doesnt have the step. Any others experiencing this? Why has no one made a proper shell holder for single stage presses?
Re: Reloading equipment for 5.7x28mm
Toaster wrote:I've been reloading old brass for a while and have run into a few problems I felt worth noting.
The RCBS shell holder destroys the rim because it has a lip on it that becomes imprinted in the brass. the Brass is also loose and wobbly in it leading to laquer scraping off one side and bullets seating cocked. In my opinion it makes it fairly unusable.
I have a Redding shell holder thats on the way, should work as it doesnt have the step. Any others experiencing this? Why has no one made a proper shell holder for single stage presses?
Actually one has been made. The company is CH4D. They are some of the best dies I have ever come across. Elite is also carrying the die set from them.
"Let us never forget that good intelligence saves American lives and protects our freedom."
-Ronald Reagan
-Ronald Reagan
Re: Reloading equipment for 5.7x28mm
I got the rcBS dies as a gift so I really didnt chose them. I picked up the shell holder at the local store,.
Ill take another look at the CH4d
Item #:40834 $9.28
Item #:40834X $9.28
Difference?
Also anyone know the difference between the 2 piece die set offered on their site and the EA is a 3 piece?
Thank all
Ill take another look at the CH4d
Item #:40834 $9.28
Item #:40834X $9.28
Difference?
Also anyone know the difference between the 2 piece die set offered on their site and the EA is a 3 piece?
Thank all
Re: Reloading equipment for 5.7x28mm
I got the rcBS dies as a gift so I really didnt chose them. I picked up the shell holder at the local store,.
Ill take another look at the CH4d
Item #:40834 $9.28
Item #:40834X $9.28
Difference?
Also anyone know the difference between the 2 piece die set offered on their site and the EA is a 3 piece?
Thank all
Ill take another look at the CH4d
Item #:40834 $9.28
Item #:40834X $9.28
Difference?
Also anyone know the difference between the 2 piece die set offered on their site and the EA is a 3 piece?
Thank all
Re: Reloading equipment for 5.7x28mm
I seriously must have lucked out with my Lee dies. Once I put a primer-nipple-channel in the shell holder, they've been nothing but perfect.
Re: Reloading equipment for 5.7x28mm
The difference between the 2 is that one has a hole in it to eject primers out from. The other is a solid flat bottom which I use when sizing the cases. I deprime in a seperate step then with sizing.
"Let us never forget that good intelligence saves American lives and protects our freedom."
-Ronald Reagan
-Ronald Reagan
- panzermk2
- Forum Supporter
- Posts: 12382
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Reloading equipment for 5.7x28mm
Toaster wrote:I got the rcBS dies as a gift so I really didnt chose them. I picked up the shell holder at the local store,.
Ill take another look at the CH4d
Item #:40834 $9.28
Item #:40834X $9.28
Difference?
grimmond wrote:The difference between the 2 is that one has a hole in it to eject primers out from. The other is a solid flat bottom which I use when sizing the cases. I deprime in a seperate step then with sizing.
We include a CH4D crimp die. Also just an FYI the set we sell has one shell holder in it, not 2 and the one is not a CH4D holder. It is from another supplier.Toaster wrote: Also anyone know the difference between the 2 piece die set offered on their site and the EA is a 3 piece?
Thank all
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
![Image](https://i.imgur.com/HDeYsHy.jpg)
XL 650 Reloading equipment for 5.7x28mm
Has anyone tried the 5.7x28 conversion kit from AZ-Born; https://az-born.com/ ? I bought a new Dillon XL650 progressive about a year ago. Am in the process of moving everything I can from the Rockchucker and Piggyback over to the new progressive. Don't get to spend a lot of time playing with it so it's been a slow go. I haven't gotten the advertised throughput out of it yet (still tweaking set-ups) but by comparison, it's a dream versus my green gear. Was majorly bummed when I found out Dillon doesn't offer a 5.7 caliber conversion kit for any of their presses. Started looking at some other internet forums and found some older threads where a couple of guys were attempting to prototype their own a few years ago but gave up after a while. Not sure why. Then I happened to come across AZ Born. Looks like a quality product and they've posted some videos on youtube so looks legit. Before I plunk down 150 clams, thought I'd ask the experts here if anyone had seen and tried this "after-market" kit.
Thanks,
Lekim
Thanks,
Lekim
Re: Reloading equipment for 5.7x28mm
GONRA loads 9mm and .45 ACP SMG ammo on my Dillon.
But one should carefully load ANY 5.7x28mm FN ammo on a SINGLE STAGE PRESS, CAREFULLY WEIGHING POWDER CHARGES, to avoid chambering issues and worse yet - KABOOMS!
But one should carefully load ANY 5.7x28mm FN ammo on a SINGLE STAGE PRESS, CAREFULLY WEIGHING POWDER CHARGES, to avoid chambering issues and worse yet - KABOOMS!
Re: Reloading equipment for 5.7x28mm
I ordered a RCBS #29 shell holder (.25 ACP) because supplier listed it as being interchangeable with 5.7x28FN. It is NOT! Too small, had to force 5.7 brass in and had a heck of a time getting it out. Be sure to order items that are 5.7 specific (RCBS #45). Beware of any supplier that lists components as being interchangeable between .25ACP and 5.7x28FN.
Re: Reloading equipment for 5.7x28mm
Damn, I wonder if the Lee #15 holder will cause the same issue..... It says it is for 25 ACP as well. I am thinking about ordering one....FNFbobcat wrote: ↑01 Nov 2020, 09:29I ordered a RCBS #29 shell holder (.25 ACP) because supplier listed it as being interchangeable with 5.7x28FN. It is NOT! Too small, had to force 5.7 brass in and had a heck of a time getting it out. Be sure to order items that are 5.7 specific (RCBS #45). Beware of any supplier that lists components as being interchangeable between .25ACP and 5.7x28FN.
Re: Reloading equipment for 5.7x28mm
I have a Lee #15. Works fine. Some brands are interchangeable, some are not.
Who is online
Users browsing this forum: Google [Bot] and 43 guests