Photo dipped reciver

Discuss rifles chambered for the 5.7x28mm; P90, PS90, and AR57.
Post Reply
BadMrFrosty
Junior Member
Posts: 33
Joined: 07 Dec 2014, 07:15
Location: PA

Photo dipped reciver

Post by BadMrFrosty » 05 May 2017, 05:29

Here's a pic of my sbr PS90 that I had the reciver done in tech tron green from jay. I'm very happy with the work that was done and appreciate the time and patience of the dipper. The only thing I need is a good low profile laser/light combo but that can wait till extra money is available.

Burris Fast Fire 3
Man cave charging handles
Man cave mag release
Man cave mag rollers
Son of Cy hammer
Amp trigger
Wolies hammer spring
Percival side rails
Percival extended buttpad
Cmmg flash hider
Cmmg 10.4 barrel
Dan Haga cheek riser
Dollar store velcro for protection against ejecting brass


Image

Image

User avatar
panzermk2
Forum Supporter
Posts: 11525
Joined: 19 Aug 2008, 15:51
Location: Around here it's more like what can we shoot through next.
Contact:

Re: Photo dipped reciver

Post by panzermk2 » 05 May 2017, 09:20

Nice and I can of course help you out with a Ringsight!

I can look into have the Ringsight dipped to match also.
Jay Wolf
Pr. Elite Ammunition

"Engineers, the oompa-loompas of science!"

Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
Image

BadMrFrosty
Junior Member
Posts: 33
Joined: 07 Dec 2014, 07:15
Location: PA

Re: Photo dipped reciver

Post by BadMrFrosty » 12 May 2017, 22:30

I might look into the green fiber optic version down the road and swap my burris out. Is that pattern available for FSN dipping? If so I'll be sending in my pistol when I have that sight ordered probably around winter time. I tool my PS90 to a range that has a factory ps90 on the wall and the range officer was comparing the finish and did FN should do way better on their casting job and was very impressed wit the dipping and cerakote on mine.

User avatar
panzermk2
Forum Supporter
Posts: 11525
Joined: 19 Aug 2008, 15:51
Location: Around here it's more like what can we shoot through next.
Contact:

Re: Photo dipped reciver

Post by panzermk2 » 22 May 2017, 08:26

Pistol should not be an issue, let me check.
Jay Wolf
Pr. Elite Ammunition

"Engineers, the oompa-loompas of science!"

Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
Image

Litehiker
Junior Member
Posts: 76
Joined: 16 Aug 2013, 18:25

Re: Photo dipped reciver

Post by Litehiker » 11 Jul 2017, 19:47

That is so spacey looking.

Litehiker
Junior Member
Posts: 76
Joined: 16 Aug 2013, 18:25

Re: Photo dipped reciver

Post by Litehiker » 10 Aug 2017, 11:00

VERY nice! SUCH baddddassery!

I have a lot of the mods you do and soon an SBR barrel and FN type flash hider.

My sight is a Vortex SPARC II red dot on a TROS Low Mount. Now it comes up perfectly to my line of sight every time. No need for a cheek piece.

BTW, I put a Magpul rail on the right side of my receiver B/C it has a flush cup hole for a sling and the Paraclip ring is an adaptor for flush cup mounts. Then I got a flush cup for the PS90 from BP Armory that I put it near the heel of the stock next to the butt pad. THEN I added my Magpul Paraclip adaptor rings to both flush cup mounts B/C my Magpul Modular Sling has Paraclips.

These Magpul Paraclip rings permit me to remove the webbing sling band from the stock which cleans it up nicely.
OR, you could skip the Paraclip ring adaptor route and just go with flush cup mounts for an even cleaner look with no protruding rings. I may do that later.

Eric B.

Post Reply

Who is online

Users browsing this forum: Google [Bot] and 1 guest